If you live in a Victorian terrace, a sandstone tenement, or a traditional Scottish semi-detached, your walls are almost certainly solid. There’s no cavity to fill. And that means most of the heat your boiler or heat pump generates is finding its way straight through the walls and out into the street.
Internal wall insulation is one of the most effective ways to fix that. It won’t change how your house looks from the outside, and done properly, it significantly reduces heat loss and improves comfort. This guide explains how it works, what it costs in Scotland in 2026, and what funding is available.
What is Internal Wall Insulation?
Internal wall insulation (IWI) is exactly what it sounds like: insulating your external walls from the inside. Insulation boards are fitted to the existing wall and then finished with plasterboard, creating a new, warmer internal surface.
The big advantage over external wall insulation is that the outside of your property looks completely unchanged. For older sandstone or brick Scottish homes, particularly any that are in conservation areas or have listed status, that’s often the only realistic option.
When is Internal Wall Insulation the Right Choice?
IWI tends to be the answer when:
- Your home has solid walls with no cavity to fill
- You can’t or don’t want to insulate externally because of cost, aesthetic, or planning constraints
- You want to target specific rooms rather than insulating the whole external envelope
- Your walls are in good condition structurally but cold to the touch
The most common scenario in Scotland is a tenement flat, Victorian terrace, or older detached home where the walls are solid stone or solid brick. Modern cavity wall fillers won’t work on these, so IWI becomes the primary insulation option.
The Installation Process: Step by Step
1. Survey and Planning
Before anything is installed, we survey the walls to check for damp, structural issues, or anything that needs addressing before insulation goes in. IWI applied over a damp wall will trap moisture and cause problems. The survey stage is non-negotiable.
2. Clearing and Preparation
Radiators, skirting boards, electrical sockets, and switches are removed from the walls being insulated. For a single room this typically takes half a day. For a whole house, a day or two.
3. Insulation Boarding
The insulation boards, typically PIR (polyisocyanurate) or mineral wool-based materials, are fitted to the wall using a combination of mechanical fixings and adhesive. We make sure the install accounts for moisture management, which is critical in Scottish properties where condensation risk is higher.
4. Plasterboarding and Finishing
A layer of plasterboard goes over the insulation, with services like sockets and switches reconfigured to the new surface. We then plaster, dry, and finish ready for decoration.
5. Reinstating
Skirtings, radiators, and sockets are refitted. We clear up and leave the room ready for you to decorate.
For a single room, the work typically takes 3 to 5 days. A whole-home job might take 2 to 3 weeks depending on scope.
Typical Costs in 2026
Internal wall insulation costs vary by wall area, the type of boards used, whether plastering and reinstatement are included, and whether services need rerouting.
As a rough guide for 2026 in Scotland:
- Single room IWI: £2,500 to £4,500
- Three-bedroom semi (front and back walls): £8,000 to £14,000
- Whole tenement flat (all external walls): £10,000 to £18,000
These are indicative figures. The actual cost depends heavily on the specific property, access, the condition of the walls, and what’s involved with reinstatement. We always survey before quoting.
What Funding is Available?
Home Energy Scotland (HES) is the main funding route for internal wall insulation in Scotland. Under the current HES scheme, homeowners can access a grant of up to £7,500 for insulation measures, which covers approximately 75% of the installation cost. The remaining balance can be covered by an optional interest-free loan.
For rural properties and island homes, an additional £1,500 uplift applies.
For a typical £10,000 IWI project, that could mean approximately £7,500 as a grant (which you don’t repay) and £2,500 as an interest-free loan repaid over the agreed term. The work could effectively be cashflow-neutral if you plan it right.
To access this funding, you need to use a TrustMark approved installer and meet HES eligibility criteria. We’re one of those installers, so we can quote you in a way that’s ready to submit straight to HES.
Choosing an Installer
Internal wall insulation in older Scottish properties is technical work. Done badly, it can cause condensation problems and damage the building. Done well, it transforms how a home feels and how much it costs to heat.
A few things to look for in an installer:
- TrustMark accreditation for the specific measure, not just generic accreditation
- Experience with traditional Scottish properties, since solid stone walls behave differently to modern brick
- Clear written quote that breaks down materials, labour, and reinstatement separately
- A process that includes a pre-survey for damp and structural condition
Heat Save Scotland carries TrustMark, MCS, and Which? Trusted Trader accreditation. We’ve been working in Glasgow and the central belt for over 20 years, and a significant portion of that work has been solid wall insulation in exactly the type of older properties that benefit most.
Ready to Find Out What’s Possible?
If you’re not sure whether your home is suitable, or you want to understand what a full IWI project would cost and how much funding you’d be eligible for, the best starting point is a free home survey. We’ll assess the walls, check for any issues, and give you a clear written quote that covers the full scope of work.



